1310nm Fiber Optic Transmitter
I. Features
The transmitting modules of this machine adopt the imported DFB laser named Agere (ORTEL, Lucent), Mitsubishi, Fujitsu, AOI and so on.
The internal RF driving amplifier and controlling circuit of this machine can ensure the best C/N. The perfect and stable circuit of optic power output and controlling circuit of the thermoelectric refrigeration device of laser module assures the user the best quality and stable working for a long time.
The internal microprocessor software has many functions such as laser monitoring, number display, trouble alarm, and on-line management. Once the working parameter of the laser is out of the fixed range, there will be a red light glistening to alarm.
The RS-232 standard connector makes it is possible to manage online and monitor in another place.
The machine adopts 19"standard shelf and it can work with the voltage from 110V to 254V.
II. Display Board Operation Guide:
Press the button "Status" in the board, the working parameter of this machine can be seen in turn as follows,
1.Model: :ST1310-02,04,06,08,10,12,14,16,18,20,22,24,26,28,30
2.Output Power: display the output power of this machine(mW).
3.Laser Temp: the laser works between 20ºC and 30ºC.If the temperature is out of this range, the red light will glisten to warm.
4.Bias Current: The bias current of the laser is the main working parameter of the laser. Only when the parameter is above 30mA, RF driving circuit can begin to work. The red light will shine to warn when the RF driving level comes out of the fixed value.
5.REFRG Current: showing the working current of heating or cooling which can make sure the standard temperature is 25ºC.
6.+ 5V test(Reads): showing internal actual Voltage of ±5V.
7.- 5V test(Reads): showing internal actual-5V.
8.+24V test(Reads): showing internal actual voltage of+24V.
III. Operating Guide:
- Please examine this machine, shelf and the power to see if the power supply is good.
- This machine adopts the switching power with high quality and high stability which makes it is suitable to work in voltage from 110V to 254 V.
- Please make sure the connector is clean before installation. Please clean the fiber connector with pure alcohol before connecting the fiber.
- After connecting the power, please turn on the power in the back of the board. The screen will show the basic information of this machine. After several seconds, the laser power will turn on automatically. If the machine is all right, the condition guide light (Laser) will turn from red to green. And the screen will show you the working condition of this machine at present.
- Press the button "STATUS", then you can see the parameters of this machine in turn.
- If all the above working condition is all right, then examine whether the RF input level can satisfy the request in the test report. If it is all right, please connect the RF input to the transmitter.
IV. Notice
- Before installation or operation of unit, please carefully go through this manual.
- ST1310 Series Transmitters should be serviced only by qualified personnel.
- Before proceeding with installation and/or operation of transmitter, please assure that transmitter is well earthed.
- ST1310 Series transmitters are Class III laser products. Use of controls, adjustments, and procedures other than those specified herein may result in hazardous laser radiation exposure.
V. Main Technical Parameters
| Model(ST1310) |
-2 |
-4 |
-6 |
-8 |
-10 |
-12 |
-14 |
-16 |
-18 |
-20 |
| Optic Power (mW) |
≥02 |
≥04 |
≥06 |
≥08 |
≥10 |
≥12 |
≥14 |
≥16 |
≥18 |
≥20 |
| Optic Power (dBm) |
3.0 |
6.0 |
7.8 |
9.0 |
10.0 |
10.8 |
11.5 |
12.0 |
12.3 |
12.8 |
| Optic Wavelength (nm) |
1290~1310 |
| Fiber Connector |
FC/APC,SC/APC,SC/UPC (Selected by the Customer) |
| Working Bandwidth (MHz) |
47~862 |
| Channels |
59 |
| CNR (dB) |
≥51 |
| CTB (dBc) |
≥65 |
| CSO (dBc) |
≥60 |
| RF Input Level (dBμV) |
Not with pre-distortion |
78±5 |
| With pre-distortion |
83±5 |
| Band Unflatness |
≤0.75 |
| Power Consumption (W) |
≤30 |
| Power Voltage (V) |
220V(110~254) |
| Working Tem (ºC) |
0~45 |
| Size (mm) |
483×370×44 |
FAQ
1. What are the payment terms that you support?
Usually, we accept T/T, PayPal, Western Union, and Alibaba Trade Assurance. You can select the terms of payment which is more convenient for you.
2. What about the lead time?
Usually, if there's stock, we ship the goods within 3~5 working days after the deposit is confirmed. If it is out of stock, the lead time depends.
3. How about the shipping?
When the package is small, we normally choose FedEx, DHL, TNT, and UPS and so on, while the goods have high weight and volume, we suggest using air or sea shipment.
4. How can I place an order?
(1) Negotiation is agreed for the product price and specifications.
(2) Proforma invoice will be sent for confirmation.
(3) After the agreement on the proforma invoice, the customer makes the deposit.
(4) Manufacturing will be started as soon as the payment is confirmed by our bank.
(5) Ship out the goods within the agreed delivery deadline.
5. Can you do OEM for us?
Yes. If there is a certain order quantity, we can do OEM including printing, logo, and customized model for you.
6. How about the Warranty?
There are 12 months for the warranty.
While the warranty is not responsible for those broken by violence or updated with other brands.
Audited Supplier 
){kind=link}